information and inspiration
for students, teachers and hobbyists
About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn  flickr

 

Assembly and Operating Instructions for HiViz.com Kits

 

For best results in viewing images, we recommend using the Firefox browser.

 

Instructions for Preparing a Flash Trigger Cord (VPC Kits)

 

Assembly instructions for other kits

 

Overview


These instructions are for connecting the output of a HiViz.com breadboard trigger circuit to a flash unit using a Vivitar 283/285HV/3700 type cord like the one shown to the right. This will allow your trigger circuit to actuate the flash directly. One end of the cord will be cut and its wires wrapped tightly around the appropriate ones from the trigger output cable. The solder joints will be covered with pieces of heat shrink tubing for electrical insulation.

 

Before you begin, gather the parts and tools below. You'll also need your HiViz.com trigger circuit or delay unit for testing.

 

Parts:
3-ft of 2-conductor cable
Vivitar 283/285HV/3700 cord
2-inch length heat shrink tubing (HST), 3/32-inch diameter

3-inch length heat shrink tubing (HST), 3/16-inch diameter

Helpful tools and supplies:
Wire stripper
15- or 30-watt soldering iron and solder
Wet sponge or towel
Lighter or matches to shrink HST

 

Click on any image for a larger view. If you want the image to open in a new tab, right click on the image and select open in new tab.

 

Preparing the VPC cord

 

Cut Vivitar cord
Stripping the wires

Start with the cord shown in the photo at the top of the page. Cut it in the middle. You'll be using the end that connects to your flash unit. See the photo to left. Save the other end, as you may later want to use for a PC-type cord.

 

Using a pair of wire strippers, carefully strip back the cut end of the cord a distance of 1 inch. You'll see a copper sheath surrounding an insulated wire. (We'll call this the central wire.) Pull back the sheath and twist the wires together as shown to the right. Then strip back the insulation on the central wire to within about 1/8 inch from the black jacket. Be sure there are no stray wires from the copper sheath that touch the other wire.

 

Next, you'll need the gray 2-conductor cable. From one end of the cable, strip back the gray insulation about 2 inches. Then strip back the red and black insulation about 3/4 inch. The result is also shown to the right.

 

Splicing the wires

Twisting the wires together

 

Sliding on the HST

There are 2 sizes of HST, 3/32-inch diameter and 3/16-inch diameter. Cut the 3/32-inch piece into two equal lengths of 1 inch. Then slide them over the red and black insulation as shown to the left.

 

Next, twist the following pairs of wires tightly together as shown to the right: i) black wire and copper sheath ii) red wire and white wire.

 

 

 

 

 

 

 

Soldering the splices

 

If you're new to soldering, see the Soldering Tips below. Then solder the splices.

 

    Soldering Tips

    • Solder in a well-lit, well-ventilated, open area. Avoid contact with all metal surfaces on the iron.

    • Keep the tip of the soldering iron clean by wiping it against a wet sponge or towel before and after each use. A clean tip should look shiny and silvery; any yellow or black material on the tip will get into the solder and may weaken your solder joint.

    • Once the tip of your soldering iron is clean, touch a bit of solder to the tip just before use. This is called tinning, and helps the solder run more evenly.

    • Heat the connection to be soldered by holding the soldering iron to it, until solder applied at the junction between the two melts and flows freely. This ensures the connection and the solder are both hot enough to yield a good solder joint. This should take no more than 10-15 seconds. After the connection is heated, try to get solder along the entire length of the connection by briskly moving the solder and iron along.

    • Avoid touching only the solder to the connection, and then the soldering iron to the solder to melt it onto the connection. The connection will be cooler than the melted solder and won’t form a good solder joint.

    • Let new solder joints cool for several seconds before examining them. There should be solder all the way around the connection, forming a rigid joint. When done, unplug your soldering iron and let it cool.
 

Shrinking the HST

 

Shrinking the HST over the splices

 

Slip each piece of 3/32-inch HST completely over the corresponding splice. Then, using a lighter or a match, move the flame smoothly back and forth along the entire length of the tubing, with the tip of the flame just beneath it. If you hold the flame too long in one spot or too closely to the tubing, you will notice smoke. If this happens, lower your flame and continue moving it back and forth. The tubing will visibly shrink, and will be acceptably tight-fitting after only 10-15 seconds of heating. See the results to the left.

 

Securing the splices

HST shrunk in place

 

Sliding the 3/16" HST onto the cable

HST covering the spliced region

 

Slide the 3/16-inch HST over the gray 2-conductor so that it completely covers the two spliced wires as shown in the photos to the left. Then use a flame as before to shrink the tubing. The result is shown to the right.

 

The completed cable is shown below. Connect the red and black wires to the output of your trigger circuit and the plug to your flash unit. In the event that your flash unit isn't triggered through the cord, try reversing the connections of the red and black wires to your breadboard. This won't hurt your flash unit or the trigger circuit, but it will let you know if you have reversed polarity.

 

 

Assembly instructions for other kits

 

 

 


About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn flickr
 
 
copyright © 1995-2018 HiViz.com