information and inspiration
for students, teachers and hobbyists
About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn  flickr

 

Assembly and Operating Instructions for HiViz.com Kits

 

For best results in viewing images, we recommend using the Firefox browser.

 

Assembly Instructions for the Multi-Trigger Enclosure

 

Early Adopters' Version

 

Assembly instructions for other kits

 

Recent corrections to the instructions are highlighted in yellow.

 

Date and time of last edit: Thursday, December 18, 2014 4:16 PM

 

 

 

Contents

What you need

Parts guide

Drilling holes in the project box lid

Adding the components to the project box lid

Wiring the box lid

Soldering some of the connections

Preparing the cables

Preparing the breadboard

Adding the battery holder

Soldering jumper wires to the box lid components

Step-by-step testing

Closing up the box and final testing

Operating Manual for the MTE

 

What you need

 

These instructions show how to build a project box enclosure for a Multi-Trigger. Here's what you need to get started:

  1. Multi-Trigger Kit with Breadboard
  2. Multi-Trigger Enclosure Kit
  3. Adapter for connecting the output cable to your flash. See either PC cord adapter or Flash-to-PC adapter.
  4. This is optional: If you want to trigger a camera shutter, you'll also need a Camera Opto-Switch Kit.
  5. Also optional: If you want to power the circuit with an AC/DC adapter, you'll need something like this. This isn't a requirement, as you can always use a 9-V battery.

Here are the tools you'll need:

  1. Drill motor and bits to drill holes in the project box lid. Bit sizes are 3/32", 1/8", 1/4", 9/32", and 5/16". (For metric equivalents in millimeters, multiply by 25.4.) You can substitute a 1/8" bit for the 3/32" one. You can get by without the 9/32" bit by drilling a 1/4" hole and filing it larger.
  2. Hammer, punch (or nail), small round file
  3. 15-30 W soldering iron and solder
  4. Wire stripper, needle-nose pliers, diagonal cutter (see images below)
  5. Wrenches or sockets to tighten components onto the project box
  6. Lighter or matches, hot glue gun and glue sticks

    Wire cutters and stripper

    Small diagonal cutter

    Needle-nose pliers

     

    In case you haven't done much soldering, here are some tips.

    Soldering Tips

    • Solder in a well-lit, well-ventilated, open area. Avoid contact with all metal surfaces on the iron.

    • Keep the tip of the soldering iron clean by wiping it against a wet sponge or towel before and after each use. A clean tip should look shiny and silvery; any yellow or black material on the tip will get into the solder and may weaken your solder joint.

    • Once the tip of your soldering iron is clean, touch a bit of solder to the tip just before use. This is called tinning, and helps the solder run more evenly.

    • Heat the connection to be soldered by holding the soldering iron to it, until solder applied at the junction between the two melts and flows freely. This ensures the connection and the solder are both hot enough to yield a good solder joint. This should take no more than 10-15 seconds. After the connection is heated, try to get solder along the entire length of the connection by briskly moving the solder and iron along.

    • Avoid touching only the solder to the connection, and then the soldering iron to the solder to melt it onto the connection. The connection will be cooler than the melted solder and won’t form a good solder joint.

    • Let new solder joints cool for several seconds before examining them. There should be solder all the way around the connection, forming a rigid joint. When done, unplug your soldering iron and let it cool.

Important: Before attempting to build the enclosure, build the Multi-Trigger on a breadboard first according to these instructions. A working Multi-Trigger is a prerequisite to integrating the circuit with the enclosure.

 

Back to contents

 

Parts Guide

 

Below is a list of the parts provided in the Multi-Trigger Enclosure Kit. Click on the photos for larger images.

 

Name HiViz.com product code Photo Quantity Function Polarity and Connections

Large project box

6.0" long x 3.5" wide x 1.875"

PB-L 1    
Single-pole single-throw toggle switch (base may be black or blue) SW1 1 Simple on-off switch for power no polarity

Single-pole double-throw toggle switch

(base may be black or blue)

SW2 3 Used to select between two circuit paths. For the MTE, the three SPDT switches select between sound and photogate inputs for the delay unit, between short and long timeouts, and between short and long delay time ranges. The center terminal is common to the two circuit paths. no polarity
Linear-taper potentiometers

LP1k

LP10k

LP100k

LP1M

4 Used as variable resistors for control of sound (1k) and photogate (10k) sensitivity and for fine (100k) and coarse (1M) delay adjustment no polarity; center terminal and on
Pointer knobs PK 4 Used as pointers for potentiometer settings  
9-V battery holder 9BH 1 9-V battery clips in to this laydown container. The supplied hook and loop strips are used to stick the holder down to the inside of the project box. red wire is positive; black is negative
Pushbutton, momentary, normally open PBO 1 Used a test button for the delay unit no polarity
Panel jack for AC/DC adapter PJ 1 Receptacle for 9-V AC/DC adapter as an alternate power source When the AC/DC adapter is not plugged into the jack, terminals 1 and 2 are shorted internally. This connection opens when the adapter is plugged in. Because of this feature, terminals 2 and 3 are used to supply power from the adapter, while terminals 1 and 2 are used to supply power from the battery. Terminal 2 is shared by the two power sources and is connected to ground.
3.5mm mono panel jack 35MJ 2 One of these is used as a receptacle for the microphone cord; the other is used as an input jack for triggers other than the on-board sound and photogate triggers. Examples include a contact trigger and a light-activated trigger.

When a plug is not inserted into the jack, terminals 2 and 3 are shorted internally. This connection opens when a plug is inserted. Terminals 2 and 3 are used to connect the sound trigger and photogate to the delay unit internally. Terminals 1 and 3 are used to connect an external trigger to the delay unit.

3.5mm stereo panel jack 35SJ 1 This is used as a receptacle for the photogate cord. Terminals 1-3 connect to the sleeve, ring, and tip respectively of the corresponding stereo plug.
3.5mm mono connector (male) 35MP 1 This is the plug for the microphone cord. The sleeve is connected to ground and the tip to the microphone input.
3.5mm stereo connector (male) 35SP 2 This is the plug for the photogate cord. One is for the interrupter-style photogate and the other for the individual emitter and detector style. The tip is connected to +9 V, the ring to the photogate input, and the sleeve to a 479-ohm dropping resistor that then goes to ground on the breadboard.
RCA panel jack RCAJ 4 These are used as output jacks to connect to a flash unit or camera. Terminal 1 is connected to ground. Terminal 2 is connected to the desired output (sound, photogate, instant or delayed timer output).
RCA connector (male) RCA-m 2 These are used as connectors on the cable from a flash unit or camera to plug into any of the four RCA panel jacks or into the adapter shown below. The sleeve is connected to ground and the tip to the desired output.
RCA female to 3.5mm male adapter 35mRCAf 1 This can be used with the 3.5mm mono panel jacks in order to adapt the connection to an RCA-style plug. The adapter cannot be used in the 3.5mm stereo panel jack.  
Red LED RLED 3 Used for power on, photogate alignment indicator, and triggering indicators. While you can use the LEDs supplied with the MT-BB, extra ones are provided in case you've trimmed the legs of those LEDs too short for use on the project box. The shorter leg is negative. This is also the leg nearest the flat on the lip of the case.
LED holder LED-M 3 Used to mount LEDs on the project box.  
100-ohm resistor 100R color code brown-black-brown 1 This is provided as an extra resistor in case the one supplied with the Multi-Trigger needs to be replaced. no polarity
1-kilohm resistor 1kR color code brown-black-red 1 This is used as a dropping resistor for the power LED. no polarity
100-kilohm resistor 100kR color code brown-black-yellow 1 This is provided as an extra resistor in case the one supplied with the Multi-Trigger needs to be replaced. no polarity
0.047-μf capacitor 047C 1 This is used to divide time intervals by 10 for the delay range selector. no polarity
0.47-μf capacitor 0.47C 1 This is an extra capacitor that you may need if you trimmed the legs of the 0.47-μf capacitor that came with the MT-BB. The shorter leg is the negative side. This is also the side with the light blue stripe.
2-conductor cable 2CA-3 3' This is used in preparing the microphone cable.  
Heat-shrink tubing       Includes 2" of 3/32" dia tubing and 3" of 3/36" dia tubing for use in construction of microphone cable  
Hook up wire   24" strands in 6 colors Ample wire is provided for all connections.  
Project box labels       Stick on labels are provided in strips to identify the components on the project box.  
Template for box lid       A paper template sized for the lid of the project box is provided in order to obtain the correct placement of holes for the components.  

 

Back to contents

 

Drilling holes in the project box lid

  1. Cut out the template if it hasn't already been cut out for you. The template is sized to fit snugly within the underside of the project box lid (that is, on the interior side of the box). Position the template inside the lid and then use a nail or punch to mark the positions of the centers of the holes to be drilled.

  2. Remove the template and drill the holes. We recommend drilling small pilot holes first, for example, 3/32" or 1/8". The plastic has a tendency to grab the bit, so hold the plastic securely. We've found that a spade bit works best for drilling the quarter-inch holes. If you don't have a 9/32" bit, you can use 1/4" and then file the hole to a larger diameter for the pushbutton.

  3. Use a round file to clean up any burrs around the holes.

Adding the components to the project box lid

 

The photos below show the top and underside views of the box lid with all the components mounted.

  1. The LED mounts have two parts, which we will call the collar and the ring. (See the Parts Guide above.) The collar is first slipped down into a hole on the project box and snapped into place. Then the LED is pushed up into the collar from below and snapped into place. The ring is then pushed over the collar from below to hold the assembly tightly.

  2. Remove the nut from each 3.5mm jack, insert the jack through the box lid from below, and screw the nut back on. Needle-nose pliers can be helpful in tightening the small, round nuts.

  3. Remove the nut from the AC/DC input jack, insert the jack through the box lid from below, and screw the nut back on. You can use a wrench on this nut.

  4. Remove the nut and lock washer from the pushbutton, insert the pushbutton through the box lid from below, slip on the washer and screw the nut back on.

  5. For an RCA jack, remove the nut and the metal tab from the jack, insert the jack through the box lid from above, slip the metal tab on under the box lid, and screw the nut on. While you can use a wrench to tighten these, keeping the jack from turning while tightening requires a strong grip on jack.
  6. The switches have a retaining ring with a key tab, a washer, and a nut. Remove all three and then insert the switch from below. Orient the slot on the threads to be on the same side as the 3/32" key hole. Then slip the retaining ring on so that the key tab slips into the 3/32" hole. Slip on the washer and nut and tighten.
  7. The potentiometers also have key tabs but these are on the body of the pot. Remove the washer and nut from a pot, slip it in from below and orient it so that the key tab passes up through the 1/4" key hole. Then put on the washer and nut and tighten.

Top viewof box lid

The positions of the Triggering Indicator and Photogate Alignment Indicator were reversed in an earlier version of the photo above. The placement indicated above is the correct one. Items 2 and 4 in the numbered list below have been corrected correspondingly.

Underside of box lid

  1. SPDT switch for timeout selection
  2. LED to indicate that the photogate is aligned
  3. SPDT switch for delay range selection
  4. LED to indicate triggering of the delay unit
  5. SPDT switch for selecting sound or photogate input to the delay unit
  6. LED to indicate power on
  7. SPST switch to turn on power
  8. 1-MΩ pot for coarse delay adjustment
  9. 100-kΩ pot for fine delay adjustment
  10. 10-kΩ pot for photogate sensitivity adjustment
  11. 1-kΩ pot for sound trigger sensitivity adjustment
  12. Input jack for microphone cable
  13. Input jack for photogate cable
  14. Output jack to trigger delayed flash
  15. Output jack to trigger delayed camera shutter
  16. Output jack to trigger camera shutter without delay (This can be switched to an instant flash output by changing a breadboard connection.)
  17. Direct sound trigger output for the most rapid response from the sound trigger. This output cannot be used with the Camera Opto-Switch.
  18. Input jack for an external trigger such as a light-activated trigger, a contact closure, or another delay unit.
  19. Pushbutton to test operation of the delay unit.
  20. Jack for AC/DC adapter input

Back to contents

 

Wiring the Box Lid

 

Some of the components on the box lid are hardwired to each other before making connections to the breadboard. The images below show the wiring from different angles so that you can see clearly what the connections are. Click on the images for larger views. Here are some things to note. (The numbers refer to View 1.)

  • The wires haven't been soldered to the connectors yet. This will come in a later step.

  • White indicates wires that will be connected to ground, and red indicates wires that will be connected to +9 V. While you don't have to use particular colors in your wiring, using a consistent color coding helps keep track of connections.

  • Two white wires are wrapped around the shorter leg of the center LED (1).
  • Two red wires each are wrapped around the longer legs of the outer LEDs (2 and 3).
  • A 1000-ohm resistor (brown-black-red) is connected between the shorter leg of one LED (4) and the terminal on the side of the 3.5mm mono jack (5).
  • A 100-ohm resistor (brown-black-brown) is connected between the center terminal of the 100k pot (6) and the right terminal (7) of the 1M pot.
View 1 View 2 View 3 View 4

 

Go ahead and wire the box lid as described above. Next you'll connect components to two of the selector switches.

 

Wiring the timeout and delay range selectors

 

Click on the images for larger views.

 

Timeout selector
Twist together a 1k (brown-black-red) and 100k (black-brown-yellow) resistor as shown.
Connect the untwisted ends of the resistors to the outer terminals of the SPDT switch (timeout selector) on the left (View 1 above). The 1k resistor connects to the left terminal.
Delay range selector
Twist one leg of a 0.047-μf capacitor around the negative leg of a 0.47-μf capacitor. The negative leg is the shorter one. There is also a light blue stripe on the same side of the capacitor as the shorter leg.
Trim the legs and bend them as shown. Go ahead and solder the twisted legs together, as this will make assembly in the next step easier.
The capacitor combination is connected to the SPDT switch adjacent to the timeout selector switch. The untwisted leg of the larger capacitor connects to the switch terminal on the left (1), the untwisted leg of the smaller capacitor connects to the switch terminal on the right (2), and the twisted leg will connect to the shorter leg of the LED to the right (3). This is the leg that has two white wires wrapped around it.

 

Back to contents

 

Soldering some of the connections

 

You're ready to solder some but not all of the connections. The ones that won't be soldered now are the ones that will have jumper wires attached later to connect to the breadboard. Here are some important tips about soldering in addition to those given previously.

 

About soldering to the legs of the LEDs: These components can be damaged by excessive heat; therefore, it's a good idea to clip a heat sink to the leg when soldering. The photo the left (click to enlarge) shows a heat sink clipped to the leg of the LED close to the red case. While heat sinks may be purchased at electrical stores, you can hold the leg with needle-nose pliers instead.

 

About soldering the switches: Don't hold the soldering iron on the switch lugs too long, as the plastic can melt.

 

About cold solder joints: This is the bane of soldering projects. If you don't heat the metal before soldering the wire, the solder may not bond with it and you can get an open circuit. You can't necessarily tell by looking that you have a cold solder joint. The best approach is prevention by using good soldering techniques. Hold the tip of the soldering iron flat against the metal surface that you're soldering to. Touch the solder to the metal nearby rather than to the soldering iron. When the metal is hot enough, the solder will flow. Flow enough solder on the connection to fill the hole and cover the connection. But don't leave the soldering iron on the metal any longer than it takes to flow the solder.

 

Click on the photo to the left to enlarge it. The green dots indicate the connections to solder now, and the magenta dots indicate connections that will be soldered later. Hopefully, you'll do a better job than we did and avoid burning the white wires. (We were using a torch and got the tip too close to some of the wires.)

An aside: Here's a problem with writing instructions for assembling kits. After you get most of the way through, you discover that you could have done something differently and better. Case in point, we realized that one of the 470-ohm resistors could be moved from the breadboard to the box lid. This would eliminate one of the jumper wires that will be needed between the box lid and the breadboard. It turns out this is an easy fix.

 

First, remove the 470-ohm resistor that goes from 1F to the ground row of the breadboard. Then connect the resistor as shown in the photo. One end connects to the tab on the side of the 3.5mm stereo jack. The other end connects to one leg of the pushbutton. Just wrap the bare wire around the wire that connects to the pushbutton. Then solder both connections.

 

Back to contents

 

Preparing the cables

 

Now is a good time to assemble the cables that you'll need to connect to the box.

 

Microphone Cable
Here's what you'll need for the microphone cable: the 3-ft length of 2-conductor cable, the 3.5mm mono connector (male), the heat-shrink tubing, and the piezoelectric disc from your Multi-Trigger. Cut the 3/32" heat-shrink tubing into two 1-inch lengths and slip them onto the red and black wires of the piezo disc. Then strip the ends of the wires about 3/4".
From one end of the gray 2-conductor cable, strip the gray insulation back 3/4". Then strip each of the red and black wires 3/4".
Twist the red wire of the piezo disc around the black wire of the 2-conductor cable. Likewise, the black wire of the disc around the red wire of the cable.
Solder the connections.
Slip the heat-shrink tubing over the soldered wires and run a lighter or match flame under the tubing to shrink it but not so close as to burn the tubing.
Slip the 3" section of 3/16" heat-shrink tubing onto the cable and over the spliced connections. Heat shrink it into place.
Remove the jacket from the 3.5mm connector and slip it over the cut end of the cable. The threaded end must be toward the cut end of the cable. Strip back the gray insulation on the free end of the cable about 1/4" and then strip the insulation on the red and black wires about 1/8".
Insert the stripped wires into the holes on the terminals of the 3.5mm mono connector. The red wire goes in the shorter terminal. Don't crimp the metal tabs around the cable yet, as this will cause the insulation to melt when you solder.
Solder the connections. Since there's so much metal, it will take some time for the soldering iron to heat the metal. Hold the tip of the iron flat on the metal to heat it up in the vicinity of where you want to solder. Touch the solder to metal and wait for it to start flowing. This is the way to ensure a good electrical connection rather than a cold solder joint.
Clip off any stray wires and then crimp the metal tabs around the gray cable.
Screw on the jacket, and your microphone cable is complete.

Photogate Cable

Now let's move on to the photogate cable. The Multi-Trigger comes with two types of photogate cables, the interrupter style and the separate emitter and detector. If you haven't already made up these cables according to the Multi-Trigger instructions, go ahead and prepare the interrupter cable now and test it with the breadboard according to those instructions. Then continue below.

You'll add a 3.5mm stereo male connector to the cut end of the photogate cable. You will have already stripped the wires for connection to the breadboard. However, they're probably stripped too far for connection to the stereo plug. So cut off the stripped wires. Then, before stripping them again, unscrew the jacket of the connector and slip it onto the cable. Now, strip the gray insulation back about 1/4" and the individual wires about 1/8".
The terminals of the connector are numbered in the photo to the left. The black wire will connect to 1, the green wire to 2, and the red wire to 3. If you have trouble getting all the strands through a hole, you can clip off the strands that won't fit.

This view shows two views of the assembly with connections soldered and stray strands clipped.
Crimp the metal tabs around the cable and screw on the jacket to complete the assembly. A second 3.5mm stereo connector is supplied with the MTE kit to attach to the other photogate cable.

Flash and Camera Cables

You should have already prepared a cable for connecting the breadboard to your flash unit using either a PC cord or a Flash-to-PC adapter such as those shown to the left. Next, you'll connect a male RCA plug to the cut end of the cord for connection to project box outputs.
You'll connect the RCA plug to the cut end of the cable. First cut off the free wires, since they'll be too long for connection to the plug. Then unscrew the jacket of the plug and slip it on the cable. If the fit is too tight, snip off part of the ridged sleeve that holds it tightly to the cable. Strip back the gray insulation about 1/4" and then strip the individual wires about 1/8".
Solder the black wire to the longer terminal and the red wire to the shorter one. Crimp the metal tabs around the gray cable.
Screw the jack back on to complete the assembly of the flash trigger cable.
If you're also planning to trigger your camera using a Camera Opto-Switch, you will have prepared for that purpose the cable shown to the left. This cable connects the trigger jack of the Opto-Switch with the breadboard. In order to be able to connect to the Multi-Trigger enclosure instead, add an RCA male connector to the cut end of the cable as you did above. The completed cable for the Opto-Switch will have a male RCA plug on each end (not shown).

 

Back to contents

 

Preparing the breadboard

 

Some of the components on the breadboard need to be removed to prepare it for connection to the enclosure. Here is the list of components to remove:

  1. both of the red LEDs
  2. the yellow 1k pot
  3. the white 10k pot
  4. the 100-ohm resistor from 10G to 14G
  5. the 1-kilohm resistor from 22C to 24C
  6. the 0.47-μf capacitor from 23H to 25G
  7. the battery clip

In addition, if there's a wire connected too 13F, remove the wire.

 

You had removed one of the 470-ohm resistors earlier. So with the components removed, the breadboard should look like the photo below. Click on the photo for an enlarged view. In case you're wondering why the 100k and 1M pots are left in place, the removal of the 100-ohm resistor effectively disconnected them from the circuit. There are also some wires on the breadboard that no longer have a function. However, it's fine to leave them on the board. You may decide later to replace the removed components for testing purposes.

Back to contents

 

Adding the battery holder

 

The photo below shows how the battery holder is connected to the breadboard and the box lid. The numbers in the list below correspond to those on the photo. You can click on the photo for an enlarged view.

  1. A 6" section of blue wire is connected to the upper terminal of the SPST switch (1).
  2. The black wire from the battery holder (4) is connected to the one remaining free terminal of the AC/DC jack (2).
  3. A 6" section of green wire is connected to the same terminal of the AC/DC jack as the red wire (3).
  4. The red wire from the battery holder is connected to the red (+9 V) column of the breadboard (6).
  5. The other end of the blue wire is connected to the ground column of the breadboard (5).
  6. The other end of the green wire is connected to the red (+9 V) column of the breadboard (6).

After making the connections, place a fresh battery in the battery holder. The power LED (7) may come on immediately. If not, flip the power switch the other direction. If the LED doesn't come on with the switch in either position, check your solder joints and make sure that the 1k resistor is connected to the shorter leg of the power LED.

 

If you have a 9-V AC/DC adapter, plug it into the AC/DC jack. With the power switch on, the power LED should light. If you remove the battery, the LED should remain lit, indicating that the battery holder is automatically disconnected from the circuit when the AC/DC adapter is plugged in.

 

After verifying operation of the power source, switch, and LED, remove the battery and/or AC/DC adapter. You may want to temporarily disconnect the breadboard so that it doesn't get in the way for the next phase of connecting jumper wires to the box lid.

 

Back to contents

 

Soldering jumper wires to the box lid components

 

Recent edits to this section (Monday, Jan. 10, 2011, 9:30 PM)

  • Position B in the photo below has been corrected. An earlier placement at the 2nd RCA jack was incorrect. The placement indicated in the photo below is the correct one.

  • Originally, there were 14 jumper wires. A 15th wire has now been added to correct a problem with the delayed flash output when using the sound trigger. This wire is the blue one at point C. This wire is soldered to the same terminal as the 100-ohm resistor and the white wire.

  • You may notice that the SPST switch at upper right in the photo below is blue, whereas the switch is black in previous photos. During testing of the box, we replaced the original switch. The new switch has a blue base but is identical in function to the previous one.

 

There will be 15 jumper wires (in addition to the three that you've already attached for the battery holder) to solder to the box lid. One end of each of these wires will be left free for connection to the breadboard later. Before cutting the wires, look at the photo below to see how the box lid will look after soldering the 15 wires. (The wires marked G, Battery holder, and +9 V are the ones you soldered previously when you attached the battery holder.) Click on the photo for an enlarged view. Each of the wires extending from the box is a 6" section. You may want to trim these down later before connecting to the breadboard; however, if you start with 6" lengths, that gives you room for adjustment. You can use whatever colors you want for the wires or you can use the same colors that we used below.

 

In addition to the wires extending beyond the boundaries of the lid, note also a blue wire extending from the left side of the SPDT switch at point A to the center terminal of the RCA jack at point B. (4th RCA jack from the left) This is another one of those cases where we realized late in the game that there was a way to eliminate one jumper wire by connecting two more terminals on the box. So go ahead and add that wire now. You can solder at point A but wait to solder at point B, because you'll be adding a jumper wire there.

 

 

Go ahead and cut your jumper wires now. Strip all the ends about 1/8". Then solder. Remember to use a heat sink when soldering the wires to the LEDs. Note that the green wire at the far upper left is wound around the twisted resistor wires.

 

When you're finished soldering, clip back the legs of the LEDs and the twisted resistors so that they won't interfere with the final assembly. Also check that the connections on the two legs of each LED aren't touching each other.

 

Back to contents

 

Step-by-step testing

 

Refer to the photo below to see where the jumper wires connect to on the breadboard. The symbol RaG means the red column next to the blue, ground column. The connections for G, Battery holder, and +9 V are shown in the section, Adding the battery holder. G2 indicates a second wire connecting to the ground column. Don't connect the wires yet, though. We like to connect them in a sequence that allows for step-by-step testing so that if something doesn't work, you can narrow down the problem. To get ready, use something, say a book, to prop the lid up on its side. Place the breadboard on the table beside the lid. You'll be connecting wires to the underside of the lid and also flipping switches and inserting plugs on the other side of the lid. We copied the photo of the top of the lid for convenient reference. Also, we provide a photo showing what the final desktop assembly will look like before closing up the box. Note the arrangement of the breadboard relative to the lid. This arrangement will make it convenient to place the breadboard inside the project box later.

Inside of project box lid showing jumper wires and connections to breadboard

The positions of 28I and 29J were reversed in an earlier version of the photo above. The current, correct version was posted Jan. 26, 2011, 7:45 PM EST.

 

The positions of the Triggering Indicator and Photogate Alignment Indicator were reversed in an earlier version of the photo below. The placement indicated below is the correct one.

Top view of box lid

Project box lid with connections of jumper wires to breadboard

 

Power test

You tested the power LED in the previous section, Adding the battery holder. Make the connections described in that section. Also connect G2 on the breadboard in the ground column but at the opposite end of the column as where G is connected. Insert a battery in the holder, turn on the power switch, and verify that the LED comes on. Then turn off the switch.

 

Photogate test

Plug in the photogate cable, preferably the interrupter cable since you don't have to mess with alignment for that one. Be sure to plug it in all the way. Connect the jumper wires 8J and 4J to the breadboard. Now turn on the power. The photogate indicator LED should light indicating that the photogate is aligned and the beam is unbroken. Now run your finger through the interrupter. The indicator LED should go out momentarily. If so, all is well to this point. Turn off the power.

 

Delay unit test

Connect 11E, 13F, RaG, 22C, and 23J. Flip the input selector switch to the PG position. Turn the Coarse Delay pot all the way clockwise. Flip the Delay Range switch (also called Divide delay) to the 0.5s position, and flip the timeout switch to the 1s position. Turn on the power and then push the test button. After a delay of about a second, the delay unit LED should turn on and stay on for about a second. Now flip the timeout switch to 0.01s. When you push the test button, you'll get the same delay as before, but the delay unit LED will flicker briefly. It won't be bright. Now flip the delay range switch to the 0.05s position. When you push the test button, there won't be noticeable delay. Flipping the switch had the effect of dividing the delay by 10. There's still a delay, though, and it would be noticeable if observing high-speed events.

 

Photogate with delay test

You should get all the same results as above if you break the photogate beam instead of pushing the test button. If breaking the photogate doesn't trigger the delay unit, you may have the input selector flipped the wrong direction.

 

Delay unit with external input test

Turn off the power. Then connect the RCA female to 3.5mm male adapter into the External Input jack. Now take a male RCA plug and unscrew the plastic jacket. Insert the plug into the adapter. Turn the power back on. With a paper clip, piece of wire, or other metallic object, short together the two bare terminals of the RCA plug. This should trigger the delay unit the same way as pushing the test button. Turn off the power and remove the RCA plug and the adapter.

 

Test of delayed flash output

Connect 15B on the breadboard. Then connect the flash cable from the delayed flash output of the MTE to your flash unit. Turn your flash and the MTE power on. You should be able to trigger the flash using the test button or by passing a finger through the interrupter. If you have the coarse delay turned up and the delay range switch to the right, there should be a noticeable delay. Turn off the power and remove the flash cable.

 

Test of camera outputs

If you're using a Camera Opto-Switch to trigger your camera, do the following test. Connect 18D and 16B on the breadboard. Then connect the trigger cable from the delayed camera output on the MTE to the TRIG jack on the Opto-Switch. Turn on the MTE and your camera and turn the Focus and Shutter switches on the Opto-Switch on. Pushing the test button on the MTE should trigger your camera shutter after a short delay. Switch the trigger cable to the instant camera output on the MTE. This time, the shutter should be triggered instantly when you press the test button. Turn off the Opto-Switch, your camera, and the MTE.

 

Test of sound trigger input

Note that the Test button will not light the delay unit LED or discharge the flash when using the configuration described below.

 

Connect 26A, 28I, 29J, and 30E on the breadboard. Disconnect the photogate cable, and connect the microphone cable to the microphone jack. Flip the input selector to PG if it isn't in that position already. This may seem counterintuitive; however, putting the input selector on PG disconnects the sound trigger from the delay unit for this test. This is important if you're using a flash unit that has high-voltage (>80 V) terminals, as the flash can burn out the 556 timer otherwise. Connect the flash cable to ST OUT. Turn the sound trigger sensitivity pot about three-fourths of the way clockwise. Now turn on the flash and the MTE power. Tap the microphone or snap your fingers. The flash should discharge. In order to adjust the sensitivity of the sound trigger, do the following. Turn the SOUND SENS knob counterclockwise until the flash will no longer discharge. The reason that the flash can't discharge at or beyond this point is because the sound trigger is holding the flash in an on state. Turn the SOUND SENS knob clockwise just enough so that you can discharge the flash again. This adjust the sound trigger for maximum sensitivity. If you wish to have less sensitivity, turn the knob further clockwise.

 

Test of sound trigger with delay

Move the flash cord to the delayed flash output jack. Flip the input selector to the microphone position to connect the sound trigger to the delay unit. With the coarse delay turned up, you should get a delayed flash when you snap your fingers.

 

In earlier testing of the delayed flash outputs, we found that the flash unit sometimes produced repetitive flashes for a single triggering event. Addition of the 15th jumper wire described above seems to have fixed this problem. If, however, the problem appears for you, try flipping the Timeout selector to 1s.

 

This completes the testing. Turn off the power and disconnect the microphone and flash cables.

 

Back to contents

 

Closing up the box and final testing

 

Lift up the box lid together with the breadboard and slip the breadboard down into the project box. The fit will get more and more snug as you push the box in. Set the battery inside the box beside the breadboard. See the photo below.

You can use the hook and loop tape supplied with the battery holder to hold it firmly in place in the project box. If you have trouble with any of the jumper wires popping out of their holes, you can use hot glue to hold them in place. When everything is ready, gently push the lid down onto the box, making sure that the jumper wires remain in place on the breadboard. You may have to bend the resistor and capacitor assemblies to get them into the box. Once the lid is in place, screw down the lid. Then you can cut the labels and stick them onto to the box as shown below.

 

 

Once you have the box assembled, run through all the tests again to insure that all the wires are still connected correctly.

 

Operating Manual for the MTE

 

 

 


About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn flickr
 
 
copyright © 1995-2018 HiViz.com