information and inspiration
for students, teachers and hobbyists
About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn  flickr

 

Assembly and Operating Instructions for HiViz.com Kits

 

For best results in viewing images, we recommend using the Firefox browser.

 

Assembly Instructions for the Output Extension Kit (MT2ext) for the Multi-Trigger 2 (Build 2)

 

Assembly instructions for other kits

 

References

Clicking on any image will open a larger version on top of the page. If you prefer to have the larger images open in a different tab or window, right click on the image and make the appropriate selection.

 

Getting started

 

We assume that you've already built a Multi-Trigger 2 and have that working. Figure 1 shows a Multi-Trigger 2 with the output extension strip mounted on the left-hand side of the project box. This is how the box will look when you're finished with this project. Figure 2 shows the box in the same orientation with the arrangement of the interior components shown. Note that the output strip is mounted on the side of the box opposite the battery.

 

Template taped to side of project box Template taped to side of project box
Figure 1. Multi-Trigger 2 with output extension strip Figure 2. Layout of interior of project box

 

Adding the resistors and SCRs to the PCB

 

Completed PCB

Solder the 2 100-Ω resistors provided in the MT2ext kit into the locations R16 and R17 on the PC board.

 

Solder the 2 EC103D SCRs into the locations SCR3 and SCR 4.

 

The completed board is shown to the left.

 

Mounting the output strip

 

Template taped to side of project box

Figure 3

Step 1

 

Remove the lid and the battery holder from the Multi-Trigger box.

Tape the template for the holes on the side of the box as shown in Figure 3.

Use a punch to mark the centers of the holes.

Remove the template and drill the holes.

Holes drilled in box

Figure 4

Box with rectangular slot in box

Figure 5

Step 2

 

The box with holes drilled is shown in Figure 4.

 

Now use a small saw blade and a file to cut out a slot as shown in Figure 5. You'll be able do all the soldering to the jacks before bolting the strip on. Also, you'll easily be able to connect the grounds to each other.

ground connections soldered

Figure 6

ground connections soldered

Figure 7

Step 3

 

The shorter terminals on the jacks are the ground terminals. You can solder all of them together. Use the black wire. Strip off all the insulation and then thread the wire through the terminals. See Figure 6.

 

Now strip the insulation from the end of the white wire and connect it to an end terminal. Solder the 4 ground lugs.

 

Connect the other four wires to the longer terminals on the jacks. We recommend connecting the colors in the order shown so that they will coincide with the instructions that follow.

all wires soldered

Figure 8

Step 4

 

Connect the other 4 wires to the longer terminals on the jacks. We recommend connecting the colors in the order show in Figure 8 so that they will coincide with the instructions that follow.

interior of box with strip mounted

Figure 9

 

soldered strip

Figure 10

 

Step 5

 

Now you can feed the wires through the slot and bolt the strip to the box as shown in the overhead view of the box in Figure 9. Note the order of the colors from top to bottom: white/blue, red, green, yellow.

 

You can also stick the strip of labels above the output jack as shown in Figure 10. Later, we'll give the significance of the labels.

box with PCB in position

Figure 11

box with PCB in position

Figure 12

Step 6

 

Place the overturned lid next to the box end-to-end as shown in Figure 11. Bend the five wires back over toward the PC board. This is the orientation most convenient for making connections.

 

Now solder the following connections. You may wish to trim the wire lengths to slightly more than the length required to reach the PC board. Then, when you close the box later, you won't have as large a mass of wires to compress.

  • blue wire to hole H
  • red wire to hole C
  • green wire to hole K
  • yellow wire to hole D
  • white wire to hole M

The completed connections are shown in Figure 12.

Template taped to side of project box

Figure 13

Step 7

 

You can now close the box. Fold the wires carefully into the box as you close it and avoid pinching wires between the lid and the base. The extended outputs are ready to use.

 

Using the outputs

 

Here's what you need to know to use the outputs:

 

I means INSTANT and D means DELAYED. These outputs are triggered at the same time as the INSTANT and DELAYED outputs on the top of the box.

 

S means SWITCH and V means VOLTAGE.

 

The SWITCH outputs can be used to trigger flash units that have high-voltage trigger circuits (up to 400 V).

 

The VOLTAGE outputs are actually voltage pulses of about 7.5V. The instant pulse is very short. The delayed pulse lasts for the same amount of time as the TIMEOUT LED is lit. Here are some examples of ways the VOLTAGE outputs can be used:

  • triggering a flash unit that requires a low voltage pulse. Some studio units have such a requirement.

  • triggering a Camera Opto-Switch. Of course, you already have camera-enabled outputs on the lid. But maybe you have an application where you want to trigger two cameras at the same time.
  • actuating a solid-state relay. You might want to use a relay to switch another device on or off. For example, if you're using a laser as the light source for the photogate, you could use a relay with a normally-closed state to switch the laser on and a normally-open state to trigger a flash. When the flash is triggered, the laser shuts off momentarily. This prevents a red spot from being on your subject in the photo.

 

 

 


About Tools Products Activities Galleries Projects FAQ Links Contact Facebook LinkedIn flickr
 
 
copyright © 1995-2018 HiViz.com